Affordable Building Concepts

Home » Uncategorized

Category Archives: Uncategorized

Newly compleated 2 story custom garage full brick.

  This is 24×30 All brick to match home fully wired.  This also was partitioned off for a 1/2 bath with entrance access for the pool area.  We build to fit your needs!  Located in Murfreesboro Tn.

Remember to stop by the Southern Home Show in Wilson County we’re going to be in Booth “40” come by and say hello ✌

Please follow and like us:

How exciting we were nominated Best Backyard Outdoor Builders in Wilson Co.

I just wanted to share the news with everyone 🙂  We are very happy to just be nominated and if you would like to vote for our company you can follow the link below.

ABC is very gracious to be in this category and we are some of the BEST Garage and Storage builders in all of Tn! 

Please follow and like us:

Making sure your Garage is weatherized for the winter!

Weatherstrip garage door seal

You probably don’t think about your garage when you think about weatherization, but you definitely should. While it may be detached from the rest of the home, garages often have attic space or even living space above them. Sometimes they house water heaters and duct-work.

If either of those are true then it is important to your home performance that you make sure both the garage door that leads in from outside and the interior door that leads to the house from the garage are properly weather sealed and that the room has proper insulation in the ceiling and walls around the water heater and around the duct-work. This also applies to any windows that your garage may have. Garages are also susceptible to moisture leaks, much the same way that basements are, and that can move into the rest of the house, so sealing is key.

Older Garages are more susceptible to moisture more so then our newly built on site garages. we make sure the garages we build you are of course water tight and will not hold moisture.  At  you’ll find many different styles of custom built garages and Storage sheds, we do go the extra mile to make sure your new garage is not going to run your electric bills up with unprofessional  building, ABC Back Yard Builders are some of the best garage builders in Middle Tn.

Please follow and like us:

Using Pressure Treated Lumber??

Pressure-treated lumber is wood that is engineered for use on projects that are exposed to the elements. Pressure-treated wood typically starts off with one of the SPF varieties (Spruce, Pine or Fir) or other similar Softwoods, and a sealant formula is pressure-applied to the wood, so that the sealant soaks into the core of the wood.

This process of pressure-treating was introduced by Dr. Karl Wolman in the early 20th century, using a formula that was arsenic-based. This formula was quite effective in protecting the wood, but had issues with toxicity, not only for those who worked with the wood, but also for any animals that came into contact with the lumber (for instance, dogs that chewed on the wood often succumbed to toxic arsenic poisoning).

How to Buy Pressure-Treated Lumber

When buying pressure-treated lumber in the home center, you’ll often find that the wood arrives in the store wet. Very wet. Almost dripping wet.

When wet, wood acts like a sponge, with the fibers (forming the grain along the long axis of the tree trunk) soaking up as much liquid as possible. As the wood begins to dry, it will shrink across the fibers considerably, but very little shrinkage will occur along the length of the boards.
With this fact in mind, when you buy pressure-treated lumber, you won’t have time to wait for it to dry before you buy it to see what boards warp and twist and which boards stay straight. Instead, you’ll need to find another way to judge what boards to buy. Inspect the long edges of the boards, looking for blemishes or weak spots that may show a tendency for the board to bend around the defect. Additionally, inspect the end grain of the wood. If possible, select wood whose grain lines cross the narrowest span of the end of the board. Boards that have arc-shaped end grain will likely cup more easily than boards whose end grain crosses the narrow span of the board.
Installing Pressure-Treated Lumber

When building a deck or outdoor project that calls for pressure-treated lumber to be installed with gaps between the wood, you’ll likely want to install each board butted against the next board as tightly as possible. When the wood begins to the process of shrinkage as it begins to dry, the gaps will appear between the boards automatically.

Additionally, to help resist cupping, position any boards with end grain in the shape of an arc so that the center of the arc-shaped grain is pointing away from the adjoining member. So, if you’re installing decking onto a framework, the center of the arc on the end grain should point upwards. Be sure to place at least one deck screw through the center of the board to help minimize the bowing as the board dries. Pre-drilling the boards before driving the screws will help maintain the integrity of the wet wood as you drive the screws. A quick change drill driver set on the end of your cordless drill will make the job quick and easy.

Safety Concerns

When working with pressure treated lumber, one should consider a few extra precautions over the normal woodworking safety rules. First of all, consider wearing a dust mask when cutting the pressure-treated lumber. Even though ACQ lumber doesn’t have the toxicity issues of previous pressure-treated woods, the sawdust can be irritating to the lungs. As such, you should also do all of the cutting of the wood outside, to allow the breeze to help dissipate any airborne sawdust.

Additionally, pressure-treated lumber should be used only on outside woodworking projects, and the wood should never be burned. Once again, this is less of a concern with newer formulations than the old arsenic-based varieties, but it is still a good rule-of-thumb by which to abide.

By: Chris Baylor

Please follow and like us:

Knowing the differences when looking for a storage shed.

I would like to take a few minutes to explain the differences between an all metal storage building and a wooden storage shed.

Sounds simple to know the differences, but don’t think so fast!

When you finally hit that point in your home that you’ll need to add more storage space and that day will come.  Maybe you’ll get rid of that extra stuff but, most likely that’s not happening as soon as you’d like.

There are 2 popular choices you may think of and one is a wooden storage shed the other is a metal storage shed?   Most of the time we start out wanting to weigh the price options then another big question is size do I have a level spot that’s adequate for a storage shed to be built onsite?  ABC will level your storage with concrete blocks, also ABC will come out to look at your spot to give you a free quote and determine just how many concrete blocks maybe needed to level the storage unit on your lot.

All Metal Storage Sheds

All metal storage sheds are not water tight to start with and the roof can be installed just perfect and you’ll still have condensation drops when the weather turns cold.  Metal roofs sweat and condensation will collect on the inside of the roof which will make it damp and tiny drops of water will fall on whatever is on the inside.

All metal garages / storage sheds are built with either 14ga or 12ga option square galvanized aluminum tubing which is 2.5 to 2.75″ the legs are 5ft OC and have metal carports or storage buildings can be wind rated with  restrictions up to 140 mph.  Metal buildings have a corner trim on the outside, but you will still see sun rays come in where the metal does not come together to form a tight seal which is not completely water tight and some people will need to spray foam in these spaces to keep  the bees and insects out.  The windows on a metal building are not insulated and no floor or foundation and you would need to pour concrete, a gravel pad or even asphalt for the install or if you chose you can sit it directly on the dirt/ground.  Now this type of metal building will be anchored to the ground, asphalt or gravel with 30″ re bar that is driven through pre-drilled holes along the bottom rails or if on concrete they will use 5” red head anchor bolts.  These types of metal sheds are just what they are “all metal sheds”.

Wooden Storage Sheds

When looking for an all wooden storage shed you have many options.  ABC can custom build a unit for you, so take look on our site at “Custom” under Storage sheds or you can choose from our standard sheds which you will see many styles here at

We can build on runners or if you’d like to have a concrete foundation poured we can quote you on that along with your unit.  ABC has a concrete crew that is excellent!  Our builders are a few of the best garage and storage builders in middle Tn! 

Roof options, shingled roof or a metal roof?   When we build an all wooden shed, we start with 4×4 runners that are notched in and not just nailed on to the floor joists which are 16” OC, smart panel is used for the walls and carries a 30-year life time manufactures warranty on the panels, not to chip, split, warp, this is not your grandfathers osb/particle board any longer that splits warps and chips!  We use 2×4’s for the framing that is 24″ OC, the floor is 3/4-inch plywood vs. 1/2-inch plywood for the floors like the Pre-built mass production  storage sheds.

We don’t just staple on the shingles without felt paper we roof it like the roof on your home also offering a 25-year shingle.   We do use an insulated vinyl window with screens, 2 vents on each end with screens to keep the insects out.  In the event, you’d like to insulate you won’t need to change out the windows first because we do think ahead!   We can custom build to fit your needs with many options!  One of our popular upgrades is a loft, 1 loft or 2 for extra storage utilizing all the space with a double loft also we can add shelving and work benches as an upgrade/option.  Check all the in’s and outs before you purchase a storage building!  ABC goes the extra mile!

Please follow and like us:

Being “Environmentally” Responsible is what we need to focus on heading into the New Year 2019!!

Our Windows_03292018

See this link above for detailed info pertaining to this article

Why Keep Old Windows?

Repairing and maintain existing windows maintains value and historic
character, is environmentally responsible and can be much less expensive.
Historic windows can be endlessly repaired whereas replacement windows
have relatively short warranties and once the window fails, the entire sash
must be replaced which creates an endless cycle of purchasing, replacing and
sending materials to the landfill. Manufactures often offer lifetime warrantees
but what they don’t make clear is that 30% of the time, a replacement window
will be replaced within 10 years. Many old windows are made of old growth
wood that is denser and therefore longer lasting than wood available today.
What About Energy Efficiency?
Multiple studies have shown that properly maintained windows with the
addition of storm windows, particularly interior storm windows, can be as
efficient as replacement windows, and also continue to maintain the integrity of
a building’s historic fenestration. While the exact figure will vary depending on
the type of window installed and whether or not a storm window is used,
studies have found that it could take 100 years or more for a replacement window to pay for itself in energy savings. In addition, the majority of energy loss is
through the roof so it may be more cost efficient to replace or increase attic insulation rather than replacing windows.
What Should I Look for When Replacement is Necessary and for New Construction?
Consider using a “sash pack” that retains both the original window casings, frame and sill, rather than full, costly, replacement of these elements.
Use simulated divided lights (SDL) with spacer bar or no muntin grills. Bars should range between 5/8” to 1 1/4”, depending on the style of the window.
Use a mullion, to divide paired or triple windows. Mullion should be 4” to 6” in width as they are creating the appearance of an historic weight pocket.
Windows used in walls with lapsiding or shingle siding may not use brick mould casings.
Windows used in walls with brick or stone cladding, should use brick mould casings.
When a casementstyle window is required for a dormer to meet emergency egress requirements, but other similar dormers on the structure have
doublehung windows, a new casement that incorporates an applied grill pattern mimicking doublehung sashes should be selected as these are readily
available from multiple common manufacturers, are more compatible with the building’s existing historic millwork, and fully meet applicable code
requirements for secondary exit of a residential sleeping space.DH windows with 2 tilt sashes also meet emergency egress requirements.
Storm windows should use blindstops and have a meeting rail that lines up with the existing meeting rail.
  • What Windows Have Already Been Reviewed and Which Districts Are They Allowed To Be Used In?
    This information is for planning purposes only and is not in any way exclusive. Replacement windows are not reviewed in Neighborhood Conservation Zoning Overlay Districts.
  • Please Click on the link provided for a detailed list of manufactures and other important info you maybe interested in when choosing a type and brand of windows for your home.
Please follow and like us:

Happy New Year!! 2019 Is Just hours away!!

 ABC wishes you a very Happy and Safe New Years Eve and New Year to come!!!! 

Please follow and like us:

“Landscapers can reduce plastic bag usage with the Leaf Burrito”

Meet the Leaf Burrito, this is a very efficient way to save time, money and the earth all at the same time!  Check out the article below and find a much easier way to get all the leaves cleaned up in no time at all!

Leaf Burrito is a reusable yard waste removal bag designed to replace single-purpose plastic bags. The bag is constructed of industrial-grade mesh and zippers allowing it to unfold like a tarp for loading yard debris and then transforms into a bag or burrito, if you will, with a few quick zips.

The history

Marc Mataya is the inventor and owner of the Leaf Burrito. He got his inspiration for the product when he was preparing for a big holiday party and had 25 bags worth of leaves rolled up in a tarp.

Photo: Leaf Burrito

He asked the garbage collectors up the street if he could still dump the leaves even though he hadn’t bagged them, and they said they’d see when they got to his house. Once they got there and dumped his tarp’s worth of leaves instantaneously versus having to rip open every single plastic bag to empty out the leaves, they told Mataya they preferred his method.

“That was the ah-ha moment,” Mataya says. “And then I put a prototype together of zippers on an actual tarp. Then we figured this is ridiculous. We’re putting $15 worth of zippers onto a $2 tarp.”

Mataya says that the company he worked with to produce the prototype also produces truck covers and noticed all the different types of mesh and decided to try that material. Ultimately, they ended up custom designing their own mesh pattern for the Leaf Burrito.

Photo: Leaf Burrito

After getting his patent, he presented his product to the city of Charlotte as a way to reduce the number of plastic bags heading to landfills and at first the city said no.

“We had to get over this whole change factor and there was some selling and on the website for city council it says that their mission statement is to be a global leader of sustainability so we kind of called them out on that,” Mataya says. “We said ‘Hey look this is a Charlotte idea. We want Charlotte to pioneer this, vet it out, model it so we can be a global leader of sustainability versus if we don’t do it in Charlotte and I go somewhere else then you’re a global follower of sustainability.’”

Eventually, the city said agreed test out the bags and now Charlotte has been servicing the Leaf Burrito for 19 months. Mataya says the garbage collectors love it.

Landscaper model

While 5’ Leaf Burrito is made for residential customers, Mataya also has a 7’ model that caters to professional landscapers.

Photo: Leaf Burrito

The commercial-sized Leaf Burrito has 10 handles on it and is designed for much bigger, heavier loads. It can hold ¾ yard of mulch or 6-12 bags of leaves.

Mataya says one way landscapers can use it is as a packable and portable wheelbarrow by unzipping one end and shaking out material as you walk.

“We tout it as being a tool that is very far from just being a leaf tool,” he says. “We literally use it for almost everything landscapers will use it for. They use it for pine straw. They’ll use it to cover the trees when transporting them. They’ll carry different colored mulch in their trailer to keep them separated. They can zip two or three of them together to do one long drag. They can put pea gravel in it.”

Mataya says some landscapers have even used it as a sling for a heavy tree rootball on a fork attachment.

The custom mesh allows the Leaf Burrito to hold up to 500-600 pounds and even if the material is cut, it will not continue to tear.

“One of the things that we’ve learned is people are used to using let’s say 40’x40’ tarp or even a 20’x20’ and then if we ship them one 7’x7 ½’ Leaf Burrito, they lay it down next to their 40’x40’ tarp and they’d say “I don’t like it. It’s too small,’” Mataya says. “So, the messaging that we’re trying to do is ‘Hey this is a toolset, just like you have two backpack blowers or two weed eaters or two whatever, you need to have at least two, ideally six on every truck, and then you get rid of all your wheelbarrows and all your tarps and plastic bags.’ And then you basically task all your guys to figure it out. What we’ve found is once they start using it, they’re addicted to it.”

Photo: Leaf Burrito

For landscapers who buy the Leaf Burrito in bulk, Mataya offers custom branding on the bags for the professional look. He says right now they’re pretty flexible on how many Leaf Burritos need to be bought before they’ll brand the bags. He says if it’s a good opportunity they’ll do it for just six bags.

“We’re talking to Ruppert Landscape right now,” he says. “They’re going to vet these out in DC in one of their larger locations.”

The employee with Ruppert who saw the Leaf Burrito immediately knew they would be great for his crews who service rooftop gardens.

Mataya says another landscaping company called Canopy based in Charlotte has been reviewing the bags not only for their own use but to potentially put their name on the residential-sized bags and then leave the leaf-filled bags on the customer’s property for the city of Charlotte to pick up.

“It is revolutionary new tool,” Mataya says. “This is not a tarp. It’s not a tarp. It’s not a garbage can. It’s something completely different. It’s reusable and going to last for many, many years, because it’s incredibly durable.”

Click here for more information about the Leaf Burrito.

Please follow and like us:

Remember a quick safety tip after Christmas and the Holidays of gift giving!

Please do not advertise all the lovely gifts you’ve received this Holiday season !!!  Do this simple task before you head to the curb!

Have a great rest of your holidays and don’t invite some of the town Grinches into your home enticing them to break into your home!

Happy New Year ahead from ABC

Hanahan Police remind citizens about leaving empty packages by the road after Christmas

Please follow and like us:

3 Steps towards fire prevention in your garage!

Fires in garages and home workshops are a serious matter. The typical garage or workshop contains a host of flammable materials, from liquids such as gasoline and paint thinner to wood, sawdust and greasy rags. Often, garages and workshops contain heat sources such as water heaters and furnaces that can ignite a fire.

As with most things involving safety, the key to keeping your garage or workshop as fireproof as possible is to make sure you have the right equipment and that you get into the habit of making the safest choices. Here are three steps to garage and workshop fire prevention that everyone can and should take.

Step 1: Establish Safe Routines

If you develop safe habits, fire prevention will become routine.

When you cut or sand wood, you create sawdust and wood chips. These small pieces of wood are much more combustible than larger boards. Sweep them up right away and you will eliminate a big source of workshop fires.

  • After using paint, stain, finishing oils or solvents, seal the containers and store them in a safe place.
  • Properly dispose of oily rags to avoid the possibility of spontaneous combustion. That means placing the rags in a steel bucket with a self-closing lid. Alternatively, hang the rags on a line in a single layer to dry. Keep them far away from heat and fire sources.

    Step 2: Practice Safe Storage

    Fires require three things: fuel, oxygen and heat. Keep those three things from coming together and you have taken a big step in reducing the chances of a fire. Good storage makes that possible.

    • Keep all combustibles away from regular sources of heat or fire, such as water heaters, space heaters, furnaces and boilers.
    • Store flammable products such as wood finishes, spray paint and paint thinner in a dedicated storage container with a closed door.

    Step 3: Buy Proper Safety Equipment

    You don’t have to spend much money to buy what you need to alert you about a fire or put a fire out before it spreads.

    • Keep a fire extinguisher in your garage or workshop, preferably stored close to an exit door. See How To Choose a Fire Extinguisher for Your Home.
    • Equip the garage or workshop with the proper type of smoke alarm. See Shopping for a Smoke Alarm and Carbon Monoxide Detector.
    • Consider installing a sprinkler system, or extending the sprinkler system in your house.
    • Stay safe this holiday season keep fire safety in the first steps of a project you are doing in your garage!!  Happy Holidays from
Please follow and like us:

Enjoy this blog? Please spread the word :)